Android wifi command

출처 : https://medium.com/@josiassena/android-manipulating-wifi-using-the-wifimanager-9af77cb04c6a

adb shell am broadcast -a android.intent.action.WIFI_ON 

adb shell am broadcast -a android.intent.action.WIFI_OFF

adb shell am broadcast -a android.intent.action.CONNECT_TO_WIFI -e ssid {wifi_ssid} -e password {pwd}

on/off

adb shell "svc wifi enable"

wpa_cli 사용

# wpa_cli                                         

wpa_cli v2.3-5.1.1

Copyright (c) 2004-2014, Jouni Malinen <j@w1.fi> and contributors

This software may be distributed under the terms of the BSD license.

See README for more details.

Using interface 'wlan0'

Interactive mode

> list_network

network id / ssid / bssid / flags

> 

> status

p2p_device_address=0e:1c:20:00:00:0c

p2p_state=IDLE

wifi_display=1

ifname=p2p0

address=0e:1c:20:00:00:0c

ifname=wlan0

address=0c:1c:20:00:00:0c

> help

commands:

  status [verbose] = get current WPA/EAPOL/EAP status

  ifname = get current interface name

  ping = pings wpa_supplicant

  relog = re-open log-file (allow rolling logs)

  note <text> = add a note to wpa_supplicant debug log

  mib = get MIB variables (dot1x, dot11)

  help [command] = show usage help

  interface [ifname] = show interfaces/select interface

  level <debug level> = change debug level

  license = show full wpa_cli license

  quit = exit wpa_cli

  set = set variables (shows list of variables when run without arguments)

  get <name> = get information

  logon = IEEE 802.1X EAPOL state machine logon

  logoff = IEEE 802.1X EAPOL state machine logoff

  pmksa = show PMKSA cache

  pmksa_flush = flush PMKSA cache entries

  reassociate = force reassociation

  reattach = force reassociation back to the same BSS

  preauthenticate <BSSID> = force preauthentication

  identity <network id> <identity> = configure identity for an SSID

  password <network id> <password> = configure password for an SSID

  new_password <network id> <password> = change password for an SSID

  pin <network id> <pin> = configure pin for an SSID

  otp <network id> <password> = configure one-time-password for an SSID

  passphrase <network id> <passphrase> = configure private key passphrase

    for an SSID

  sim <network id> <pin> = report SIM operation result

  bssid <network id> <BSSID> = set preferred BSSID for an SSID

  blacklist <BSSID> = add a BSSID to the blacklist

  blacklist clear = clear the blacklist

  blacklist = display the blacklist

  log_level <level> [<timestamp>] = update the log level/timestamp

  log_level = display the current log level and log options

  list_networks = list configured networks

  select_network <network id> = select a network (disable others)

  enable_network <network id> = enable a network

  disable_network <network id> = disable a network

  add_network = add a network

  remove_network <network id> = remove a network

  set_network <network id> <variable> <value> = set network variables (shows

    list of variables when run without arguments)

  get_network <network id> <variable> = get network variables

  dup_network <src network id> <dst network id> <variable> = duplicate network variables

  list_creds = list configured credentials

  add_cred = add a credential

  remove_cred <cred id> = remove a credential

  set_cred <cred id> <variable> <value> = set credential variables

  get_cred <cred id> <variable> = get credential variables

  save_config = save the current configuration

  disconnect = disconnect and wait for reassociate/reconnect command before

    connecting

  reconnect = like reassociate, but only takes effect if already disconnected

  scan = request new BSS scan

  scan_results = get latest scan results

  bss <<idx> | <bssid>> = get detailed scan result info

  get_capability <eap/pairwise/group/key_mgmt/proto/auth_alg/channels/freq/modes> = get capabilies

  reconfigure = force wpa_supplicant to re-read its configuration file

  terminate = terminate wpa_supplicant

  interface_add <ifname> <confname> <driver> <ctrl_interface> <driver_param>

    <bridge_name> = adds new interface, all parameters but <ifname>

    are optional

  interface_remove <ifname> = removes the interface

  interface_list = list available interfaces

  ap_scan <value> = set ap_scan parameter

  scan_interval <value> = set scan_interval parameter (in seconds)

  bss_expire_age <value> = set BSS expiration age parameter

  bss_expire_count <value> = set BSS expiration scan count parameter

  bss_flush <value> = set BSS flush age (0 by default)

  stkstart <addr> = request STK negotiation with <addr>

  ft_ds <addr> = request over-the-DS FT with <addr>

  wps_pbc [BSSID] = start Wi-Fi Protected Setup: Push Button Configuration

  wps_pin <BSSID> [PIN] = start WPS PIN method (returns PIN, if not hardcoded)

  wps_check_pin <PIN> = verify PIN checksum

  wps_cancel Cancels the pending WPS operation

  wps_nfc [BSSID] = start Wi-Fi Protected Setup: NFC

  wps_nfc_config_token <WPS|NDEF> = build configuration token

  wps_nfc_token <WPS|NDEF> = create password token

  wps_nfc_tag_read <hexdump of payload> = report read NFC tag with WPS data

  nfc_get_handover_req <NDEF> <WPS> = create NFC handover request

  nfc_get_handover_sel <NDEF> <WPS> = create NFC handover select

  nfc_report_handover <role> <type> <hexdump of req> <hexdump of sel> = report completed NFC handover

  wps_reg <BSSID> <AP PIN> = start WPS Registrar to configure an AP

  wps_ap_pin [params..] = enable/disable AP PIN

  wps_er_start [IP address] = start Wi-Fi Protected Setup External Registrar

  wps_er_stop = stop Wi-Fi Protected Setup External Registrar

  wps_er_pin <UUID> <PIN> = add an Enrollee PIN to External Registrar

  wps_er_pbc <UUID> = accept an Enrollee PBC using External Registrar

  wps_er_learn <UUID> <PIN> = learn AP configuration

  wps_er_set_config <UUID> <network id> = set AP configuration for enrolling

  wps_er_config <UUID> <PIN> <SSID> <auth> <encr> <key> = configure AP

  wps_er_nfc_config_token <WPS/NDEF> <UUID> = build NFC configuration token

  ibss_rsn <addr> = request RSN authentication with <addr> in IBSS

  sta <addr> = get information about an associated station (AP)

  all_sta = get information about all associated stations (AP)

  deauthenticate <addr> = deauthenticate a station

  disassociate <addr> = disassociate a station

  chan_switch <cs_count> <freq> [sec_channel_offset=] [center_freq1=] [center_freq2=] [bandwidth=] [blocktx] [ht|vht] = CSA parameters

  suspend = notification of suspend/hibernate

  resume = notification of resume/thaw

  roam <addr> = roam to the specified BSS

  p2p_find [timeout] [type=*] = find P2P Devices for up-to timeout seconds

  p2p_stop_find = stop P2P Devices search

  p2p_connect <addr> <"pbc"|PIN> [ht40] = connect to a P2P Device

  p2p_listen [timeout] = listen for P2P Devices for up-to timeout seconds

  p2p_group_remove <ifname> = remove P2P group interface (terminate group if GO)

  p2p_group_add [ht40] = add a new P2P group (local end as GO)

  p2p_prov_disc <addr> <method> = request provisioning discovery

  p2p_get_passphrase = get the passphrase for a group (GO only)

  p2p_serv_disc_req <addr> <TLVs> = schedule service discovery request

  p2p_serv_disc_cancel_req <id> = cancel pending service discovery request

  p2p_serv_disc_resp <freq> <addr> <dialog token> <TLVs> = service discovery response

  p2p_service_update = indicate change in local services

  p2p_serv_disc_external <external> = set external processing of service discovery

  p2p_service_flush = remove all stored service entries

  p2p_service_add <bonjour|upnp> <query|version> <response|service> = add a local service

  p2p_service_del <bonjour|upnp> <query|version> [|service] = remove a local service

  p2p_reject <addr> = reject connection attempts from a specific peer

  p2p_invite <cmd> [peer=addr] = invite peer

  p2p_peers [discovered] = list known (optionally, only fully discovered) P2P peers

  p2p_peer <address> = show information about known P2P peer

  p2p_set <field> <value> = set a P2P parameter

  p2p_flush = flush P2P state

  p2p_cancel = cancel P2P group formation

  p2p_unauthorize <address> = unauthorize a peer

  p2p_presence_req [<duration> <interval>] [<duration> <interval>] = request GO presence

  p2p_ext_listen [<period> <interval>] = set extended listen timing

  p2p_remove_client <address|iface=address> = remove a peer from all groups

  wfd_subelem_set <subelem> [contents] = set Wi-Fi Display subelement

  wfd_subelem_get <subelem> = get Wi-Fi Display subelement

  fetch_anqp = fetch ANQP information for all APs

  stop_fetch_anqp = stop fetch_anqp operation

  interworking_select [auto] = perform Interworking network selection

  interworking_connect <BSSID> = connect using Interworking credentials

  anqp_get <addr> <info id>[,<info id>]... = request ANQP information

  gas_request <addr> <AdvProtoID> [QueryReq] = GAS request

  gas_response_get <addr> <dialog token> [start,len] = Fetch last GAS response

  hs20_anqp_get <addr> <subtype>[,<subtype>]... = request HS 2.0 ANQP information

  nai_home_realm_list <addr> <home realm> = get HS20 nai home realm list

  hs20_icon_request <addr> <icon name> = get Hotspot 2.0 OSU icon

  fetch_osu = fetch OSU provider information from all APs

  cancel_fetch_osu = cancel fetch_osu command

  sta_autoconnect <0/1> = disable/enable automatic reconnection

  tdls_discover <addr> = request TDLS discovery with <addr>

  tdls_setup <addr> = request TDLS setup with <addr>

  tdls_teardown <addr> = tear down TDLS with <addr>

  signal_poll = get signal parameters

  pktcnt_poll = get TX/RX packet counters

  reauthenticate = trigger IEEE 802.1X/EAPOL reauthentication

  wnm_sleep <enter/exit> [interval=#] = enter/exit WNM-Sleep mode

  wnm_bss_query <query reason> = Send BSS Transition Management Query

  raw <params..> = Sent unprocessed command

  flush = flush wpa_supplicant state

  driver <command> = driver private commands

  radio_work = radio_work <show/add/done>

  vendor <vendor id> <command id> [<hex formatted command argument>] = Send vendor command

# ifconfig
# netcfg
lo       UP    127.0.0.1       255.0.0.0       0x00000049
eth0     UP    192.168.40.128  255.255.255.0   0x00001043
eth1     DOWN  0.0.0.0         0.0.0.0         0x00001002
# ifconfig -a
-a: No such device
# ifconfig eth0
eth0: ip 192.168.40.128 mask 255.255.255.0 flags [up broadcast running multicast]
#